This article demonstrates how to configure a basic firewall using iptables. Using the iptables program, you can explicitly grant and deny access to selected services running on your server, as well as to selected IP addresses.
ImportantYou must have root access to the server to follow the procedures described below.
About iptables
The iptables program enables you to view and modify the Linux kernel’s built-in network packet filtering capabilities. You can grant or deny access to specific network services (such as SSH, HTTP, and so on), as well as permit or block specific IP addresses from connecting to the server.
To do this, you define sets of rules, which are grouped together intochains. By default, iptables uses three chains: INPUT (for incoming packets), FORWARD (for forwarding packets), and OUTPUT (for outgoing packets). In this article we will only work with the INPUT chain to selectively block and accept incoming packets to the server.
The iptables program is included in most major Linux distributions by default, including Debian, Ubuntu, AlmaLinux and Fedora.
Adding rules
By default, iptables does not have any rules defined. You can verify this yourself on a new server by typing the following command:
You should see the following output:
As you can see, there are no targets and no destinations defined. So let’s add some basic rules. At the command prompt, type the following commands:
In all of these commands, the -A option instructs iptables to append the rule to the end of the specified chain (in this case, the INPUT chain). Let’s step through each command:
-
The first command permits all packets for the local loopback interface. Many programs use the loopback interface, so it is a good idea to accept packets on it.
-
The second command uses the -m option to load the state module. This module determines and monitors a packet’s state, which can be NEW, ESTABLISHED, or RELATED. In this rule, we accept incoming packets that belong to a connection that has already been established.
-
The third command accepts incoming TCP connections on port 22 (SSH).
🚧 Important
Make sure you use the correct SSH port number for your account. For example, some types of hosting accounts use a different port for SSH, such as 7822.
-
The last command drops (rejects) incoming packets that do not match any of the preceding rules.
Now if you type the iptables -L command, you should see the following output:
To test the configuration, try connecting to the server using SSH. It should allow you to connect. Connections on any other ports, however (such as an HTTP connection on port 80) will be rejected.
Inserting rules
The set of rules we defined above is pretty limited. If SSH is the only incoming connection you want to allow, then you’re all set. Most likely, though, you will need to add access to services as you configure your server.
However, if we just add a rule using the -A option shown above, it will be the last rule in the chain, right after our DROP rule. Because iptables works through rules in sequence, this means that it will never get to the new rule, because the packet will have already been dropped. Therefore, we need a way to insert new rules into the chain.
The -I option enables us to insert a new rule anywhere in the chain. Let’s insert a rule that allows incoming TCP connections on port 80 (HTTP). We want the rule to come just before the DROP rule, which is currently the fourth rule in the chain:
This inserts our HTTP rule in the fourth line, and pushes the DROP rule down to the fifth line. Now if you type the iptables -L command, you should see the following output:
To quickly view the line numbers for all of the rules in a chain, type the following command: Blocking an IP address
The rules above define access by service (SSH, HTTP, etc.). However, you can also set rules that permit or block specific IP addresses.
For example, suppose you find in your server log files that there are repeated SSH login attempts from a particular IP address. To block all subsequent SSH connections from the IP address, type the following command. Replace rulenum with the rule number in the chain, and replace xxx.xxx.xxx.xxx with the IP address to block:
To block all traffic from an IP address regardless of the service requested, type the following command:
Deleting rules
To delete a rule, use the -D option. You need to know the number of the rule you want to delete (just as you must know the number when you insert a rule). The following command demonstrates how to delete the fifth rule from the INPUT chain:
If you want to delete all of the rules at once, type the following command:
Saving rules
If you reboot the server now, all of the rules you defined will be erased. To maintain rules across system restarts, you must save them. The steps to do this depend on the Linux distribution you are running.
Debian and Ubuntu
To save the iptables rules on a server running Debian or Ubuntu, follow these steps:
-
At the command prompt, type the following command:
-
During package installation, at the Save current IPv4 rules? prompt, press Enter.
-
At the Save current IPv6 rules? prompt, press Tab, and then press Enter.
📘 Note
Steps 2 to 3 only appear once during initial package installation. If you make any subsequent modifications to iptables rules, type the following command to save them:
AlmaLinux and Fedora
To save the iptables rules on a server running AlmaLinux or Fedora, type the following command:
This article is only a brief introduction to some of iptables’ capabilities. For more information about iptables, type the following command at the command prompt:
Related articles
